Why is my Fisher & Paykel DishDrawer showing an error code?

Fisher & Paykel DishDrawers use fault codes (F1-F9 and beyond) to indicate specific issues like drain pump failure, water inlet problems, or motor faults. Our Pinellas County technicians can read and clear these codes and perform the correct repair same day.

My Fisher & Paykel refrigerator is not cooling but the freezer works fine — why?

This is a classic symptom of a failed evaporator fan motor or a defrost system problem allowing frost to block airflow to the fridge compartment. Our technicians can diagnose and fix this quickly throughout Pinellas County.

Is Fisher & Paykel appliance repair expensive in Pinellas County?

Fisher & Paykel repairs are generally very cost-effective compared to replacing the appliance. We provide upfront, transparent pricing before any work begins. Most repairs are completed in a single visit across Clearwater, Palm Harbor, and St. Petersburg.

Do you carry Fisher & Paykel parts in stock in Pinellas County?

We stock the most common Fisher & Paykel parts for dishwashers, refrigerators, and washers. For specialty parts, we can typically source and receive them within 1-2 business days to minimize your downtime.

Do you repair Fisher & Paykel SmartDrive washing machines?

Yes! Fisher & Paykel SmartDrive washers use a unique direct-drive motor system that requires specialized diagnostic knowledge. We repair SmartDrive washers that won't spin, won't agitate, leak, or display fault codes throughout Pinellas County, FL.

My GE Monogram refrigerator is not cooling — what's wrong?

GE Monogram cooling failures are most often caused by a faulty sealed system, a failed evaporator fan motor, a dirty condenser, or a defrost system issue. Our Pinellas County technicians carry diagnostic tools specific to GE Monogram's advanced control systems and offer same-day service.

My GE Cafe range is showing an F error code — what does it mean?

GE Cafe F codes typically indicate oven sensor failures, control board faults, or ignition issues on gas models. We can diagnose the exact fault and repair it in most cases on the first visit throughout Clearwater, Palm Harbor, and St. Petersburg.

My GE Profile Opal nugget ice maker stopped making ice — can you fix it?

Yes! We repair GE Profile Opal ice makers including issues with water lines, pump failures, ice chute jams, and control board faults. The Opal is a very popular unit throughout Pinellas County and we see these repairs frequently.

Why is my GE Cafe dishwasher not draining?

A GE Cafe dishwasher that won't drain is usually caused by a clogged drain hose, a faulty drain pump, or a blocked filter. This is one of the most common dishwasher repairs and can usually be resolved in a single visit anywhere in Pinellas County.

Do you repair GE Monogram integrated column refrigerators in Pinellas County?

Yes! GE Monogram integrated column refrigerators and freezers are among the most sophisticated refrigeration units on the market. Our technicians are experienced with their dual compressor systems, precision temperature controls, and integrated panel configurations. We serve all of Pinellas County including Clearwater, Palm Harbor, Safety Harbor, and Belleair.

What is the difference between GE Monogram, GE Cafe, and GE Profile?

GE Monogram is GE's top luxury line with fully integrated professional-grade appliances. GE Cafe is the designer line with customizable hardware finishes. GE Profile is the smart mid-premium line with features like Opal ice makers and SmartHQ connectivity. All three lines require experienced technicians for proper repair.

Why is my KitchenAid refrigerator ice maker not making ice?

KitchenAid ice maker failures are usually caused by a frozen fill tube, faulty water inlet valve, failed ice maker module, or a clogged water filter. We carry common KitchenAid ice maker parts in stock for same-day repair throughout Pinellas County.

My KitchenAid oven is not heating evenly — what's the cause?

Uneven heating in a KitchenAid oven is typically caused by a failing bake or broil element, a faulty temperature sensor, or a convection fan issue. We can calibrate and repair KitchenAid ovens to factory specifications in Clearwater, Palm Harbor, Largo, and all of Pinellas County.

My KitchenAid dishwasher is leaving residue on dishes — why?

Poor cleaning is usually caused by a clogged spray arm, a worn wash pump, incorrect detergent, or low water temperature. Our technicians can inspect the full wash system and restore cleaning performance with a same-day service visit.

My KitchenAid washer is showing an F/E error code — what does it mean?

KitchenAid F and E fault codes indicate specific component failures such as motor control issues (F7E1), door latch problems (F5E1), or drain errors (F9E1). Our technicians use professional diagnostic tools to read and resolve these faults throughout Pinellas County.

Is KitchenAid the same as Whirlpool?

KitchenAid is owned by Whirlpool Corporation but is built to a higher premium standard with distinct components and engineering. Our technicians are experienced with both KitchenAid and Whirlpool product lines across all of Pinellas County.

Do you repair KitchenAid wine coolers in Pinellas County?

Yes! We repair KitchenAid undercounter wine coolers and beverage centers that are not cooling, making noise, displaying error codes, or have compressor and fan issues. Same-day service available throughout Tarpon Springs, Clearwater, and St. Petersburg.

My Bosch dishwasher is showing E24 or E25 — what does it mean?

E24 indicates a draining error and E25 usually points to a blocked drain pump filter or a faulty drain pump impeller. These are the most common Bosch dishwasher errors and are usually resolved in one visit throughout Clearwater, Palm Harbor, Largo, and all of Pinellas County.

My Miele dishwasher shows F14 — what's wrong?

Miele F14 indicates a heating fault, typically caused by a failed heating element or NTC temperature sensor. Our technicians carry Miele-specific heating components and can resolve this efficiently with same-day service in Pinellas County.

Why is my Bosch refrigerator making a loud humming noise?

Loud humming in a Bosch refrigerator is typically caused by a failing evaporator fan motor, condenser fan motor, or a compressor working harder than normal due to dirty condenser coils. We can diagnose and fix this quickly anywhere in Pinellas County.

Is Miele appliance repair worth it or should I replace?

Miele appliances are engineered to last 20+ years. In most cases, repairing a Miele is far more economical than replacing it. We provide honest repair vs. replace assessments and transparent pricing for all Miele repairs in Pinellas County.

My Bosch 800 series induction cooktop won't turn on — why?

Bosch induction cooktops that won't power on often have a control board fault, a failed power relay, or a child lock accidentally activated. Our technicians can diagnose and resolve Bosch induction cooktop issues efficiently throughout Pinellas County.

Do you repair Miele washing machines and heat pump dryers in Pinellas County?

Yes! We repair Miele washing machines with F codes, door lock failures, drum bearing issues, and drainage faults. For Miele heat pump dryers we handle condenser cleaning issues, heat pump system faults, and control board replacements throughout Tarpon Springs, Clearwater, and St. Petersburg.

What Bosch dishwasher series do you repair?

We repair all Bosch dishwasher series including the 100, 300, 500, 800, and Benchmark series. Whether your unit has an E15 flood protection error, a circulation pump failure, or a door latch issue, our technicians can resolve it with same-day service in Pinellas County.

Professional Appliance Repair Blog | Tips & Guides in Pinellas County

🧊 "My Sub-Zero Fridge Stopped Cooling!" – What We Found (and Fixed) in Tarpon Springs

Professional Appliance Repair
Jul 16, 2025
3 min read

Sub-Zero refrigerators are the gold standard. Quiet. Powerful. Built to last.

But when a loyal customer in Tarpon Springs called us in a panic—“My fridge is warm but the freezer’s still cold”—we knew it was time to dive deep into a premium system gone quiet.

Let’s walk you through what happened, how we fixed it, and why it’s a common (but preventable) issue with high-end refrigerators.

🚨 The Problem Why My Sub-Zero Fridge Stopped Cooling: Warm Fridge, Cold Freezer

Lauren had owned her Sub-Zero 690 for over 15 years with zero problems—until one day, the top fridge started getting warm. Milk was spoiling. Lettuce wilted overnight. Meanwhile, the freezer was still working fine.

Sub-Zero refrigerator not cooling — Sub-Zero repair Tarpon Springs

“We didn’t hear the usual fan sound anymore. And the fridge temperature just kept climbing. We were afraid the whole unit was failing.”

Sub-Zeros rarely fail all at once. This kind of uneven cooling pointed to a very specific issue.

🔍 What We Found

We hear you as My Sub-Zero Fridge Stopped Cooling!, Our tech arrived same-day. After removing the interior panels and doing a full system check, here’s what we uncovered:

The evaporator fan motor in the fridge section had stopped spinning
Ice had built up inside the air duct, blocking cold air from circulating
The thermistor (temperature sensor) was reading erratically
The condenser coils were packed with dust and overdue for cleaning

The good news? The sealed system (compressor, refrigerant lines) was perfectly fine. This was a mechanical + airflow issue—fixable, fast.

🛠️ The Fix

We replaced the failed fan motor with an OEM Sub-Zero part, installed a new thermistor, and used steam to defrost the clogged air ducts. While inside, we also cleaned the condenser coils to help the system breathe and improve energy efficiency.

💡 Bonus: We recalibrated the door hinges and checked gasket seals to ensure proper airflow, preventing future frost buildup.

Within hours, the fridge dropped from 61°F to a perfect 37°F.

👏 The Result

“You saved us thousands. We were about to start shopping for a new fridge, and now it’s working better than ever. I’m beyond impressed.”— Lauren W., Tarpon Springs

💡 What Causes Sub-Zero Cooling Issues Like This?

Even elite appliances like Sub-Zero have moving parts that wear out over time. Common issues we see:

Symptom	Likely Cause	Our Fix
Fridge warm, freezer cold	Fan motor or airflow blockage	Replace fan, defrost ducts
Loud humming or clicking	Motor strain or failing relay	Replace relay/board
Ice near vents or panels	Airflow imbalance	Clear ducts, check sensors
Temps keep fluctuating	Bad thermistor	Replace + recalibrate
No cooling at all	Compressor or sealed system issue	Full diagnostic & repair

🧰 Why Customers Trust Us with Sub-Zero Repairs

Sub-Zero repairs aren’t basic appliance work—they require real knowledge, OEM parts, and the confidence to diagnose complex systems. We bring all of that, plus:

4,800+ repairs completed
Factory-trained, EPA-certified techs
Only genuine Sub-Zero parts used
Honest pricing with 12-month warranty
Fast response in Palm Harbor, Tarpon Springs, Clearwater & more

🏡 Serving These Areas:

Tarpon Springs
Palm Harbor
Clearwater
Westchase
Odessa
Dunedin
Belleair
Trinity
Holiday
Safety Harbor

📞 Need Help With Your Sub-Zero?

Whether your fridge is warm, noisy, or totally quiet—we can fix it. Don’t wait for it to get worse. Call us today for same-day or next-day repair.

Professional Appliance Repair 📲 (727) 361‑9800 🌐 www.profapplianceservice.com

🌀 Dryer Repair or Why Your Dryer Is Screaming—and What We Did to Fix It

Professional Appliance Repair
Jul 14, 2025
4 min read

#ApplianceRepair #RefrigeratorRepair #FridgeNotCooling #WasherDryerRepair #ProfessionalApplianceRepair #LocalApplianceRepair #SameDayRepair #EmergencyApplianceRepair #CertifiedTechnician #WhirlpoolRepair #LGRepair #SamsungRepair #GERepair #MonogramRepair #SubZeroRepair #KitchenAidRepair #VikingApplianceRepair #TrueRefrigerator #WineCoolerRepair #TampaBay #ClearwaterFL #StPetersburgFL #LargoFL #PalmHarborFL #TarponSpringsFL #DunedinFL #SafetyHarbor #SeminoleFL #PinellasCounty

You know that high-pitched squeal your dryer suddenly started making? You're not alone. Loud, shrieking dryer noise is one of the most common—and most annoying—problems homeowners face. The good news? It’s fixable. Quickly.

At Professional Appliance Repair, we recently handled a case in Palm Harbor that perfectly illustrates the issue—and the solution.

👨‍🔧 Dryer Repair Case Study:

“My Samsung Dryer Sounds Like It’s Dying”

Customer: Allison K., Palm Harbor, FLAppliance: Samsung electric dryer, ~6 years oldProblem: Extremely loud squealing noise during each cycleSymptoms:

Noise gets louder with heavier loads
Started suddenly
No heat issues, just unbearable sound

🔍 Diagnosis: Common Causes of Dryer Squealing Noises

After performing a full inspection, we found the culprit:

✅ Worn-out idler pulley — the bearing was dried up and screeching

✅ Dry, cracked drum support rollers — uneven rotation caused vibration

✅ Drive belt wear — while still intact, it had signs of cracking and contributed to the pitch

Other possible causes we often see:

Misaligned drum
Worn rear drum bearing (especially in GE dryers)
Object trapped between drum and seal (coins, zippers)

🔧 The Repair Process

We disassembled the dryer cabinet, carefully removed the drum, and replaced:

Idler pulley
Drum rollers (with OEM parts)
Drive belt (preventive)

We also cleaned out lint buildup around the motor housing—an overlooked source of overheating and future motor wear.

🕒 Time on site:

1.5 hours🔩 Parts used: All OEM, compatible with Samsung DVE45T3200W

🧰 Cost: Less than replacing the dryer—and far quieter!

✅ Brand-Specific Notes

🌀 Samsung & LG:

• Known for premature roller wear• Plastic pulleys often squeak without warning• Drum removal can be tight in stackable models

⚙️ Whirlpool, Maytag:

• Heavy-duty rollers, but idler pulleys still fail• Lint trap and blower wheel areas need regular cleaning

🧺 GE:

• Rear drum bearing often fails (metal-on-metal screeching)• Fix involves full rear panel disassembly

🗣️ What the Customer Said

“We thought we needed a new dryer. The sound was unbearable. You came the same day and fixed everything in one visit. It’s quieter than when we bought it!”— Allison K., Palm Harbor, FL

🚨 Don’t Ignore That Noise

If your dryer is making a loud squealing, grinding, or rumbling noise, it’s telling you something’s wrong. And the longer you wait, the more expensive the repair can get.

We’ve fixed hundreds of dryers across Palm Harbor, Tarpon Springs, and Clearwater. We know every brand, every model, and every trick.

📍 Serving Areas

Palm Harbor
Tarpon Springs
Clearwater
Odessa
Holiday
Dunedin
Westchase

📞 Ready to Fix It?

Noisy dryer? We’ll silence it.

🧰 6,800+ successful repairs

⚡ Same-day/next-day availability

🔧 Honest diagnostics & flat-rate pricing

🌟 Local, EPA-certified professionals

👉 Call now: (727) 361‑9800Or book online: www.profapplianceservice.com

🧠 AI 🔌 Intelligence in Modern Appliances—and What to Do When They Break

Professional Appliance Repair
Jul 4, 2025
2 min read

Range Repair — Appliance Repair Same day

Imagine a fridge that scans groceries, a washer that senses fabric, or an oven that auto-adjusts from afar. AI and IoT have transformed kitchen appliances—but they also bring new repair challenges. With over 4,800 service calls in Palm Harbor & Tarpon Springs, here’s how we fix what others can't.

🔍 What Makes an Appliance “AI”?

Modern "smart" models use:

Machine learning & load sensing (LG Washer’s AI DD™ adapts cycles automatically)
Computer vision (GE’s SmartProbe & Kitchen Hub detect doneness & ingredients) 1
Voice assistants & app control (Samsung Bespoke Fridge with Bixby suggests meals)
Predictive maintenance & adaptive energy use (Bosch Series 8, Samsung AI washers, GE smart fridge)

🔧 Why AI Breaks—and How We Fix It

AI adds complexity—so we stay ahead with factory-trained techs and diagnostics tools:

Washers stuck in sensing/error loops: sensor recalibration, firmware updates
Fridges won’t connect to app: Wi-Fi antenna and modem tuning
Ovens not preheating via app: board resets, sensor recalibration
Smart fridges not recognizing items/voice: camera recalibration, Bixby relinking
Smart probes/app Bugs: firmware updates and replacing faulty probes

🏅 Top AI Appliance Brands & Features

Brand & Tech	AI Feature	What We Fix
LG ThinQ / AI DD	Detects fabric type	Board/firmware resets
Samsung SmartThings & Bespoke AI	App control, Bixby meal suggestions	WiFi sync, camera fixes
GE Profile / SmartProbe	Smart probes with SmartHQ app	Probe replacement, app pairing
Bosch Home Connect Series 8	Adaptive cooking programs	Sensor calibration, app config

🗣️ Real Feedback from Local Customers

“Our LG ThinQ washer hung on ‘sensing’ mode. Other techs said ‘just buy new.’ We fixed it in one visit — updated firmware and realigned sensors.”— Mark S., Palm Harbor

“Samsung fridge AI lost Wi‑Fi after an update. They traced antenna wiring issues, hooked it back up and reconnected Bixby—fridge now suggests dinner again!”— Elena P., Tarpon Springs

🌟 Why Choose Us?

Technicians trained on AI & smart boards
OEM parts and software updates
Same-day service and clean work
Trust from 6,800+ jobs—approved by locals, hotels, and property managers

📍 Serving Palm Harbor, Tarpon Springs, Clearwater, Holiday, Odessa, Westchase

📞 Call us now: (727) 361‑9800 or book online 👉 profapplianceservice.com

✅ Final Take

Modern appliances are smarter—but smarter things still break. With AI boards, cameras, sensors, and voice functionality, they need expert care. We fix more than just parts—we restore your smart home experience.

#SmartApplianceRepair #AIFridgeFix #PalmHarborTech #SmartWasherRepair #BoschHomeConnect #GEProfileSmartProbe #SamsungBespokeAI #LGThinQRepair #ProfessionalApplianceRepair